COMPONENT LOCATION

STARTER SWITCH

SERVICE INFORMATION

GENERAL

NOTICE

• A halogen headlight bulb becomes very hot while the headlight is ON, and remain hot for a while after it is turned OFF. Be sure to let it cool down before servicing.

• Note the following when replacing the halogen headlight bulb.

— Wear clean gloves while replacing the bulb. Do not put finger prints on the headlight bulb, as they may create hot spots on the bulb and cause is to fail.

— If you touch the bulb with your bare hands, clean it with a cloth moistened with denatured alcohol to prevent its early failure.

— Be sure to install the dust cover after replacing the bulb.

• Check the battery condition before performing any inspection that requires proper battery voltage.

• A continuity test can be made with the switches installed on the motorcycle.

SPECIFICATIONS

ITEM

SPECIFICATIONS

Headlight

12 V-35W

Tail light

LED

Fuse

15 A

TORQUE VALUES

0.7 N m (0.1 kgf-m, 0.5 Ibf ft) 4.2 N-m (0.4 kgf-m, 3.1 Ibf ft) 0.7 N-m (0.1 kgf-m, 0.5 Ibf-ft)

Headlight mounting screw Tail light mounting screw Tail light wire clamp screw

HEADLIGHT

BULB REPLACEMENT

DUST COVER

DUST COVER

COMPONENT LOCATION

Remove the front visor.

— ’05 -’07: (page 3-5)

— After ’07: (page 3-6)

Remove the dust cover.

BULB SOCKET

’05 — ’07 shown-

COMPONENT LOCATION

While pushing the bulb socket, turn it counterclock­wise and remove the bulb socket.

Remove the bulb.

NOTICE

Avoid touching the halogen headlight bulb. Finger prints can create hot spots that cause a bulb to break.

’05 — ’07 shown:

COMPONENT LOCATION

Install a new bulb into the headlight unit while aligning the tab with the groove of the headlight unit.

If you touch the bulb with your bare hands, clean it with a cloth moistened with denatured alcohol to prevent early bulb failure.

05 — ’07 shown

COMPONENT LOCATIONWhile pushing the bulb socket, turn it clockwise and install the bulb socket.

BULB SOCKET

TOP" MARK

Install the dust cover tightly against the headlight unit with its "TOP" mark facing up.

Install the front visor.

— ’05-’07: (page 3-5)

— After ’07: (page 3-6)

DUST COVER

"TOP" MARK

DUST COVER

ADJUSTING SCREW/ SPRING

CLAMP

MOUNTING

SCREWS

REMOVAL/INSTALLATION (’05 — ’07)

Remove the front visor (page 3-5).

Remove the vertical beam adjusting screw, spring, mounting screws, clamp and headlight unit.

Installation is in the reverse order of removal.

TORQUE:

Headlight mounting screw:

0.7 N-m (0.1 kgf m, 0.5 Ibf ft)

Adjust the headlight aim (page 4-31).

HEADLIGHT UNIT!

COMPONENT LOCATIONREMOVAL/INSTALLATION (After ’07)

MOUNTING SCREWS

ADJUSTING SCREW/ SPRING

Remove the front visor (page 3-6).

Remove the vertical beam adjusting screw, spring, mounting screws and headlight unit.

Installation is in the reverse order of removal.

TORQUE:

Headlight mounting screw:

0. 7 N m (0.1 kgf m, 0.5 Ibf ft)

Adjust the headlight aim (page 4-31).

HEADLIGHT UNIT

Добавить комментарий

Ваш e-mail не будет опубликован. Обязательные поля помечены *

Confirm that you are not a bot - select a man with raised hand: